|
DIAbide Profiling Endmillsfor Machining Non-Metallic Materialsand Non-ferrous Metals |
Catalog |
|
DIAbide Profiling Endmillsfor Machining Non-Metallic Materialsand Non-ferrous Metals |
Catalog |
| To select the optimum tool coating type for your application refer to the MAC table. |
Append MAC number to part number when ordering. Available from
stock. MAC 1 (DLC) coating available; allow one to two week lead time.sp3 can supply other profiling endmill configurations on special order. |
PROFILING ENDMILLS – FRACTIONAL INCH SIZES |
||||||||||
| Cutting Diameter |
Shank Diameter |
Length of Cut |
Overall Length |
Reach | Corner Radius |
Number of Flutes |
Part No. | MAC 5 | ||
| images/square | Corner Radius |
Ball Nose |
||||||||
 |
||||||||||
1/16 |
1/8 | 1/16 | 3 | .75 | — | 4 | 12850 | — | — | |
| 1/16 | 3 | .75 | — | 4 | — | — | 12810 | |
||
|
||||||||||
3/32 |
1/8 | 3/32 | 3 | .75 | — | 4 | 12851 | — | — | |
| 3/32 | 3 | .75 | — | 4 | — | — | 12811 | |
||
|
||||||||||
1/8 |
1/8 | 1/8 | 3 | 1.50 | — | 4 | 12852 | — | — | |
| 1/8 | 3 | 1.50 | .015 | 4 | — | 12853 | — | |
||
| 1/8 | 3 | 1.50 | — | 4 | — | — | 12812 | |
||
| 1/8 | 4 | 1.50 | — | 4 | 12854 | — | — | |
||
| 1/8 | 4 | 1.50 | .015 | 4 | — | 12855 | — | |
||
|
||||||||||
3/16 |
3/16 | 3/16 | 3 | 1.87 | — | 4 | — | — | 12816 | |
|
||||||||||
1/4 |
1/4 | 1/4 | 4 | 2.00 | — | 4 | 12856 | — | — | |
| 1/4 | 4 | 2.00 | .015 | 4 | — | 12857 | — | |
||
| 1/4 | 4 | 2.00 | .062 | 4 | — | 12858 | — | |
||
| 1/4 | 4 | 2.00 | — | 4 | — | — | 12813 | |
||
|
||||||||||
5/16 |
5/16 | 5/16 | 4 | 2.00 | — | 4 | — | — | 12815 | |
|
||||||||||
3/8 |
3/8 | 3/8 | 4 | 2.00 | — | 4 | 12859 | — | — | |
| 3/8 | 4 | 2.00 | 0.015 | 4 | — | 12860 | — | |
||
| 3/8 | 4 | 2.00 | — | 4 | — | — | 12814 | |
||
|
||||||||||
1/2 |
1/2 | 1/2 | 4 | 2.00 | — | 4 | 12861 | — | — | |
| 1/2 | 4 | 2.00 | 0.015 | 4 | — | 12862 | — | |
||
| 1/2 | 4 | 2.00 | — | 4 | — | — | 12818 | |
||
| All dimensions are in inches. |
||||||||||
| Back to top |
| Tolerances – Standard Fractional Inch Endmills | |||||
| All dimensions in inches |
Cutting Diameter |
Shank Diameter |
Runout | Length of Cut |
Overall Length |
| MAC 5 | +0.000/-0.002 | -0.0000/-0.0004 | <0.001 | +.060/-.000 | ±.060 |
| Back to top |
PROFILING ENDMILLS – METRIC SIZES |
||||||||||
| Cutting Diameter |
Shank Diameter |
Length of Cut |
Overall Length |
Reach | Corner Radius |
Number of Flutes |
Part No. | MAC 5 | ||
| images/square | Corner Radius |
Ball Nose |
||||||||
|
||||||||||
3.0 |
3 | 3 | 75 | 20 | — | 4 | 12470 | — | — | |
| 3 | 75 | 20 | 0.2 | 4 | — | 12471 | — | |
||
| 3 | 75 | 20 | — | 4 | — | — | 12472 | |
||
|
||||||||||
6.0 |
6 | 6 | 100 | 38 | — | 4 | 12473 | — | — | |
| 6 | 100 | 38 | 0.5 | 4 | — | 12474 | — | |
||
| 6 | 100 | 38 | — | 4 | — | — | 12475 | |
||
|
||||||||||
8.0 |
8 | 8 | 100 | 50 | — | 4 | 12476 | — | — | |
| 8 | 100 | 50 | 0.5 | 4 | — | 12477 | — | |
||
| 8 | 100 | 50 | — | 4 | — | — | 124782 | |
||
|
|
||||||||||
10.0 |
10 | 10 | 100 | 50 | — | 4 | 12479 | — | — | |
| 10 | 100 | 50 | 0.5 | 4 | — | 12480 | |
|||
| 10 | 100 | 50 | — | 4 | — | — | 12481 | |
||
|
||||||||||
12.0 |
12 | 12 | 100 | 50 | — | 4 | 12482 | — | — | |
| 12 | 100 | 50 | 0.5 | 4 | — | 12483 | — | |
||
| 12 | 100 | 50 | — | 4 | — | — | 12484 | |
||
| All dimensions are in mm. |
||||||||||
| Back to top |
| Tolerances –Metric Endmills | |||||
| All dimensions in mm |
Cutting Diameter |
Shank Diameter |
Runout | Length of Cut |
Overall Length |
| MAC 5 | +0.000/-0.002 | -0.0000/-0.0004 | <0.001 | +.060/-.000 | ±.060 |
| Back to top |
 |
To order call 888-547-4156 |
